Product Overview US VTech interior paint interior latex paint green odor, odor peculiar use of advanced technology, do not add flavor, odor fast, real odor, so you get rid of the odor problems, add more charcoal factor, light easy loose to make room for pure and natural, fresh and green. Scope designed for concrete and cement mortar exterior wall surface design professional primer. For chalking old paint and absorb the force of a strong wall to save topcoat and improve adhesion of the coating surface. Also for not brushing off a brick wall, cement plaster, plasterboard, asbestos and other surfaces. Stir well before dilution. For best results brushing, roller coating, brushing according to the actual situation of not more than 10% (by volume) of water dilution (increase or decrease feel appropriate under construction). After two characteristics have mold alkali practical efficacy hiding power construction tools easy to clean paint finish, please use the water to wash all utensils. Theoretical consumption of paint 12 m2 / l / single pass (dry film 30 microns) (varies roughness and the dilution ratio of the actual construction of the surface, the consumption of paint are different). Dry recoat schedule: 30 minutes / 25 ℃, hard dry: 60 minutes / 25 ℃. Recoat: 2 hours / 25 ℃, 7 days brushing paint, more than seven days, as the case may require re-coating, drying time will vary with ambient temperature and humidity changes. Technical parameters specific gravity: 1.24 (± 0.01) kg / l (Note: The consumption of paint, specific gravity and other data is only suitable for white and light-colored product). Storage Store at 0-35 ℃ cool, clean, dry place, the rest of the paint should be good closures, impurities can cause paint deterioration. If you do not open the product and by safekeeping. Surface treatment before painting, exterior wall must be firm, dry, clean and free from dust, may take a different approach to the circumstances. New wall (unpainted): ① ensure adequate dry wall, concrete, plaster walls should have adequate conservation. ② humidity brick wall, mortar wall humidity should be below 10%. ③ alkaline cement wall concrete, cement mortar walls alkaline PH value of less than 10 should guarantee. ④ remove grout residue and protruding parts of the wall surface with the appropriate tools. ⑤ small grease dirt and dust using a mild detergent or solvent cleaning, or scrub with a damp cloth to thoroughly remove all stains. ⑥ the wall surface and repair large cracks with cement mortar depression; small voids and cracks such as paint can not fill level, needed special external waterproof putty repair (partial repair as much as possible). After using the repair materials, wall needs to be thoroughly dried and polished smooth. Old wall (unpainted): ① First check the wall condition, treatment by the method mentioned earlier, depending on surface defects. ② clear accumulation of drifting wall. ③ wall breeding mold or moss with water cannons removed and treated with antifungal solution, then rinse and dry. Old wall (painted over paint): ① original coating intact attached to the wall, due to erosion produced powder, powder layer can be removed by water cannons and dry. ② old film when the emergence of local damage, with the appropriate tools to remove the damaged part of the film to remain firm edge and patch formation. After ③ old when damaged and there is powder coating phenomenon, it should be scooped up and patch formation, brushing the US supporting accessible primer. ④ old textured surface coating such as a firm can be directly re-painted; otherwise require the use of sandblasting manner. Construction conditions to reach the substrate before coating the coating requires confirmation. Please do not wet or cold weather (temperatures below 5 ℃ or above 35 ℃, relative humidity greater than 85%) case of construction, or can not achieve the desired coating effect, when the case of fog, wind, rain, the should stop outdoor construction. Select the appropriate construction methods and appropriate construction tools, according to the recommendation of the construction process for construction work. Control Coating interval, after reaching recoat time before the next coat of paint brushing. Recoat time is too short can cause the following coating dry slowly, wrinkling, blistering, and poor water resistance and adhesion.